Day/Night
Ultra Wide Dynamic
Fixed Dome Camera
NTSC / PAL
HD4U
HD4UX
User Guide
Document 800-00031 – Rev A – 04/08
Warnings
Installation and servicing should be performed only by qualified and experienced technicians
to conform to all local codes and to maintain your warranty.
WARNING! 12 VDC/24 VAC models require the use of CSA Certified/UL
Listed Class 2 power adapters to ensure compliance with
electrical safety standards.
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of
this product (applicable in the European Union and other European
countries with separate collection systems). This product should be
disposed of, at the end of its useful life, as per applicable local laws,
regulations, and procedures.
Explanation of Graphical Symbols
THIS SYMBOL INDICATES
THAT DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
CAUTION
RISK OF
ELECTRICSHOCK
DO NOT OPEN
WITHIN THE UNIT.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
THE COVER. NO USER-SERVICEABLE
PARTS INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
THIS SYMBOL INDICATES
THAT IMPORTANT OPERATING
AND MAINTENANCE
INSTRUCTIONS ACCOMPANY
THIS UNIT.
Document 800-00031 Rev A
04/08
3
FCC Compliance Statement
Information to the User: This equipment has been tested and found to comply with the limits
for a Class B digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to
provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference. For example, try reorienting or relocating the receiving antenna, increasing the
separation between the equipment and receiver, or connecting the equipment to an outlet on a
different circuit.
Caution
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Manufacturer’s Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is compliant with the
essential protection requirements of the EMC directive 2004/108/EC and the Low Voltage
Directive LVD 2006/95/EC, conforming to the requirements of standards EN 55013 for
emissions, EN 50130-4 for immunity, and EN 60065 for Electrical Equipment safety.
4
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Unpack Everything . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Mounting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connecting Cables Through the Housing Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Electrical Box Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connecting the Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Adjusting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Adjusting the Lens Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Camera Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Camera Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
OSD Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Configuring the WDR Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Optimizing the Camera Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Setting the Camera Image Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Setting the Day/Night Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Restoring Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installing the Enclosure Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Solving Common Technical Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Warranty and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cable Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
HD4U Mounting Template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Document 800-00031 Rev A
04/08
5
Introduction
The unobtrusive, low-profile design of the HD4U/X CCTV Camera is ideal for indoor and
outdoor installations in commercial and residential venues.
Before You Begin
Please read this guide carefully before you install the HD4U/X CCTV Camera.
Keep this guide for future reference.
Unpack Everything
Check that the items received match those listed on the order form and packing slip. The
HD4U/X packing box should include, in addition to this User Guide:
•
One fully-assembled HD4U/X camera, including factory-installed pigtail power and video
connectors
•
•
•
•
•
One service monitor cable
One wall mount adapter plate
One HD4U/X hardware kit
One bag containing mounting screws
One Product warranty
If any parts are missing or damaged, contact the dealer you purchased the camera from or call
6
Equipment Required
You will require the following tools to complete the installation:
•
•
Phillips screwdriver
Tools supplied in the hardware kit (three Allen keys: one each for the security screw on the
lid, the conduit plug locking screw, and the lens locking screw)
•
Side-cutters
Document 800-00031 Rev A
04/08
7
Installation
The HD4U/X is weather-sealed for indoor or outdoor locations. The HD4U/X is a fully-integrated
enclosure with camera and lens. The wiring can be completely concealed to reduce the risk of
tampering.
HD4U/X dome
enclosure
Mounting the Camera
The HD4U/X Camera is designed to be surface mounted on a wall or ceiling. Before you mount
the camera, use the mounting template provided to mark and pre-drill the holes.
8
Connecting Cables Through the Housing Base
For installations that require pulling cables through the grommet located in the bottom of the
base:
opening should be only big enough to feed the cable assembly through.
2. Pull the cabling through the opening.
3. Apply appropriate sealant around the opening to prevent moisture from entering the
housing.
Figure 1
Cable Connection Through Grommet
!
Base gasket opening
Document 800-00031 Rev A
04/08
9
Connecting Cables Through the Side Conduit
1. Peel back the bottom flat gasket below the side conduit just enough to expose the security
screw.
3. Use a flat screwdriver to unscrew the conduit plug.
4. Pull the cables through the hole.
5. Apply appropriate sealant around the opening to prevent moisture from entering the
housing.
Figure 2
Cable Connection Through Side Conduit
side conduit
security screw
Allen key
(supplied)
10
Electrical Box Installations
Figure 3 illustrates how to mount the HD4U/X directly to a 4S electrical box or directly to wall or
ceiling. For 4S electrical box installations, you can use the supplied adapter plate to cover
ceiling or wall imperfections around the electrical box opening.
Figure 3
4S Electrical Box Installation
Electrical box
(not supplied)
Ceiling/wall
Secure the adapter
plate to the 4S
electrical box using
appropriate screws
(not supplied)
Adapter plate
(use is optional)
HD4U/X base
Secure the HD4U/X base
with screws appropriate to
your installation (supplied)
For surface mount
installations (without an
electrical box), use
#6-1 7/16 inch slotted Type
A screws (x4) supplied
Note
Honeywell recommends that you orient the conduit plug facing downwards (wall
mount installations) to prevent moisture from entering the housing.
Document 800-00031 Rev A
04/08
11
Figure 4 illustrates how to mount the HD4U/X directly to a double gang or single gang electrical
box.
Figure 4
Double Gang/Single Gang Electrical Box Installation (Single Gang Shown)
Electrical box
(not supplied)
Ceiling/wall
HD4U/X base
Secure the HD4U/X base
with screws appropriate to
your installation (not
supplied)
For surface mount
installations (without an
electrical box), use
#6-1 7/16 inch slotted Type
A screws (x4) supplied
12
Connecting the Wiring
Follow Figure 5 to connect the video and power wires.
Figure 5
Wiring Connection
Video: female BNC
Power
Note
For secure installations,
surface-mounted cables should
be protected by plastic or metal
cable covers.
Red+
Black –
Adjusting the Camera
To adjust the HD4U/X Camera:
1. Apply 12 VDC or 24 VAC power to the camera and monitor the video signal.
2. Loosen the screws that lock the gimbal assembly in place (see Figure 6).
3. Adjust the camera carrier to the desired view.
4. Tighten the screws to lock the gimbal assembly in place.
Note
Orient the camera as shown in Figure 6 to maintain the correct picture orientation.
Document 800-00031 Rev A
04/08
13
Figure 6
Gimbal Adjustment
Top view
Angle view
Locking screw. Loosen to
adjust Horizontal (B).
Setscrews (x2). Loosen to
adjust Pan (C). Other setscrew
located on opposite side.
Locking
screw
Joystick (5 way) See
B
C
Legend
Set focal length
(bottom)
Set focus
(top)
A
A = Tilt rotation
B = Horizontal rotation
C = Pan rotation
Adjusting the Lens Focus
Lenses are pre-focused at the factory but may require a final adjustment after installation
because the optical effect of the dome may cause a slight defocusing of the lens.
TECH TIP! To check the focus, hold the dome over the lens while making any adjustments.
To adjust the camera direction, view angle and focus, connect the service monitor cable
(supplied) to the video monitor output.
14
Camera Setup
Camera Functions
- Press down on the joystick and hold two seconds
to access the MAIN MENU.
- Press down to enter a screen or select a menu
option.
Joystick
control
(5 way)
#, ꢀ
Move horizontally to and between menus and
options
!,"
Move vertically to and between menus and options
“…” indicates submenus
MENU
CAMERA SETUP ..
VIEWING ..
WDR PRESETS ..
DAY/NIGHT SETUP ..
VERSION INFO ..
To leave the screen and return to the previous menu,
select PREVIOUS PAGE, and then press down on
the joystick.
Move the
Select a menu,
thenpressdown
the joystick to
enter the
joystick#,ꢀ
to change
the status.
To save your changes, select SAVE & EXIT, and then
press down on the joystick . Your settings remain in
effect when power is turned off, then on again.
RESTORE DEFAULTS <NO>
>
EXIT
EXIT W/O SAVE.
submenu.
OSD Menu Structure
MENU
4 Setup menus for easy
programming
VERSION
INFO
EXIT
DAY/NIGHT
SETUP
RESTORE
DEFAULTS
CAMERA
SETUP
WDR PRESETS
VIEWING
Menu:
FW Rev:
NO
YES
D/N CONTROL …
NIGHT MODE
TDN DELAY
DIG SLOW SHUTTER …
SYNC MODE
AGC …
WHITE BALANCE
AI THOLD
FLIP
SAVE & EXIT
EXIT W/O SAVE
PRESETS
FLUORESCENT
ID DISPLAY …
SHARPNESS
BRIGHTNESS
RESOLUTION
COLOR ADJ.
Document 800-00031 Rev A
04/08
15
Configuring the WDR Presets
Select the appropriate camera mode for the lighting conditions.
MENU
WDR PRESETS
WDR (Wide Dynamic Range) PRESETS
INDOOR
>
MENU
CAMERA SETUP ..
VIEWING ..
WDR PRESETS .. INDOOR>
DAY/NIGHT SETUP ..
VERSION ..
WDR PRESETS
LOADING DOCK
GAMING
LICENSE PLATE
OUTDOOR
CUSTOM
ATM
>PRESETS ..
FLUORESCENT
<CUSTOM.>
OFF
>
PREVIOUS PAGE
RESTORE DEFAULTS
LOBBY
EXIT
SAVE & EXIT
The table below explains the Preset options on the WDR PRESETS menu. Double-click a
Preset to display a read-only screen showing the factory settings. INDOOR is the default.
WDR Preset
INDOOR
LOADING DOCK
GAMING
LICENSE PLATE
OUTDOOR
ATM
Area of Interest
Full scene
Center scene
Full scene spot glare
Full scene spot glare
Full scene
WDR
Wide
Wide
Exposure
Highlights
Highlights
Medium Highlights
Medium Shadows
Ultrawide Highlights
Ultrawide Shadows
Center scene
Center scene
LOBBY
Wide
Shadows
<CUSTOM>
Opens the CUSTOM screen where you can adjust the limits of the wide dynamic range by
moving the cursor.
CUSTOM
WDR LIMIT 36
AES
PREVIOUS PAGE .
0
36
!
SHADOWS
>
Note Watch the changes on the video monitor for the best results.
>WDR LIMIT Adjust the dynamic range to change the camera’s light optimization. Reduce the level to
lower the dynamic range. Adjust the slider from 0 to 36 (default is 20).
16
<AES>
The AES (Automatic Electronic Shutter) feature compensates for excessive light levels by
automatically adjusting the shutter speed of the camera. Select from:
HIGHLIGHTS for optimum exposure of bright areas of the scene.
SHADOWS for optimum exposure of dark areas of the scene.
Optimizing the Camera Setup
Note
This menu is for advanced users only.
The table below explains the options on the CAMERA SETUP menu. Each selection on this
menu takes you to a separate screen (see description below).
CAMERA SETUP
DIG SLOW SHUTTER
SYNC MODE ..
AGC
X2 ..
LL ..
26 dB
WHITE BALANCE ..
AI THOLD -18 -42
>
60
!
DIG SLOW
SHUTTER
Digital Slow Shutter. Select a shutter speed, from x2 to x32. Notice that the AGC value
> CUSTOM.
Opens the SLOW SHUTTER SETUP menu where you select the optimum exposure
adjustment. Shutter mode options are:
SLOW SHUTTER SETUP
SHUT MODE
PREVIOUS PAGE .
SHUT PRI ..
>
SHUT PRI (Priority) to select the sensitivity LIMIT from 0 to 60 (26 is the default), or the
sensitivity THRESHOLD from 22 to 34 (22 is the default). See figure on left.
GAIN PRI (Priority) to adjust the noise LIMIT in the image, from 0 to 60 (26 is the
default), or adjust the gain THRESHOLD from 28 to 42 (28 is the default).
AUTO SHUTTER--SHUT PRI
MANUAL to manually set the sensitivity LIMIT from 0 to 60 (26 is the default).
LIMIT
>
!
26
0
60
34
THRESHOLD
22 22
PREVIOUS PAGE .
!
Document 800-00031 Rev A
04/08
17
>SYNC
Synchronize the vertical interval sync pulse of your camera with other equipment to
reduce the effect of picture roll on the monitor. Select either:
LINE LOCK
0
<INTERNAL> (default) for cameras using DC power or when line lock is not required,
or
V PHASE
>
!
519 624
PREVIOUS PAGE .
<LINE LOCK> to open the Line Lock screen where you can adjust the Vertical Phase
(V PHASE) from 0 to 624 (519 is the default).
>AGC
Automatic Gain Control. This setting affects the day/night threshold. A higher AGC value
results in the camera switching from day to night mode at lower levels. While observing
a video monitor, adjust the noise in the image, from 0 dB to 36 dB.
>WHITE BALANCE Opens the WHITE BALANCE menu where you set how the camera tracks to accept
different lighting conditions within the color range of 2000K to 11000K.
<ATW Normal> The ATW Normal (default) and ATW Desat (Desaturation) options open the WHITE
<ATW Desat>
BALANCE LIMITS screen where you set the Low and High white balance limits (2100K
to 8800K) while observing the video monitor.
WHITE BALANCE LIMITS
ATW Desat is useful for low light conditions.
LOW LIMIT
>
!
2K 2100 5.5K
HIGH LIMIT
!
5.5K 8800 11K
PREVIOUS PAGE .
<AWB>
Opens the PUSH AWB CONFIRM screen where you save your AWB settings to have
them take effect, or select CANCEL. Auto white balance ensures that color integrity is
maintained.
Caution Selecting Save will overwrite all previous settings.
<MANUAL …>
Opens the MANUAL WHITE BALANCE menu where you adjust the color settings while
observing the scene in the video monitor. Options are:
MANUAL WHITE BALANCE
<KELVIN> Move the cursor to set the TINT, from 2K to 11K (2900 is the default).
ADJ MODE
PREVIOUS PAGE .
<R/B ..>
>
<R/B> Adjust the RED and BLUE settings, from -20 to 20. The default red is -18 and
the default blue is 13.
Use this feature when:
R/B ADJUST
•
Non-standard lighting exists or color lighting temperature exceeds the range of the
RED
BLUE
-18 -20
13 -20
20
20
>
!
camera.
!
PREVIOUS PAGE .
•
A significant part of the scene contains a single color or a completely red or blue
background.
18
<ATW Xtnd>
Automatic Tracking White Balance (Extended Range). Continuously monitors the color
temperature while an internal micro controller sets the white balance. Select this mode
when the scene illumination varies between indoor scenes and outdoor scene lighting.
Operating color temperature range is 2000K to 11000K.
>ADVANCED
WHITE BAL ..
Opens the ADVANCED WHITE BALANCE menu where you can adjust the magenta or
the white balance bias. Options are:
<MGNTA CTRL>. Select
ADVANCED WHITE BALANCE
<OFF>, <ON>, or
MGNTA CTRL
WB BIAS
-2K
PREVIOUS PAGE .
OFF
2K
>
<CUSTOM> to open the MAGENTA CONTROL screen and, while observing the
video monitor, adjust the level, from 0 to 100 (5 is the default).
!
0
<WB BIAS> to adjust the level from -2K to 2K (0 is the default).
>AI THOLD
Adjust the Automatic Iris (AI) threshold, from -42 to 60 (-18 is the default).
Note When using a manual iris lens, set the AI threshold to -42 (recommended).
The AI threshold is factory set to -18 for all WDR presets.
Setting the Camera Image Properties
The table below explains the options on the VIEWING menu.
VIEWING
FLIP
ID DISPLAY
SHARPNESS
OFF
<OFF>
NORMAL
>
BRIGHTNESS 110 80
130
!
RESOLUTION
COLOR ADJ.
NORMAL
0
-8
8
!
PREVIOUS PAGE .
Document 800-00031 Rev A
04/08
19
>FLIP
Select either:
<ON> to reverse the image horizontally on the video monitor, or
<OFF> (default)
> ID DISPLAY.
Select ON to open the CAMERA ID SETUP screen where you can add a CAMERA
ID (title) of up to 8 characters.
CAMERA ID SETUP
Move the cursor (>) to CAMERA ID, then press down on the joystick. The first
character appears. Press #, or ꢀto change the character, then press down on the
joystick to move to the next character.
CAMERA ID
ID POSITION
>
UP-LEFT
PREVIOUS PAGE .
When you are satisfied, press &, or'and move the cursor to another item.
>ID POSITION
>SHARPNESS
Select where you want the Camera ID to appear on the monitor screen Select from
the list:
<UP-LEFT>, <UP-CENTER>, <UP-RIGHT>, <DOWN-LEFT>, <DOWN-
RIGHT>
Select the level of sharpness of the image. Choices are:
<NORMAL> (default)
<SHARP>
<SOFT>
>BRIGHTNESS
>RESOLUTION
While observing the video monitor, move the cursor to adjust the overall brightness
level, from 80 to 130 (110 is the default).
Select the camera resolution. Choices are:
<NORMAL> (default)
<HIGH>
>COLOR ADJ
While observing the video monitor, move the cursor to adjust the color saturation,
from -8 to 8 (0 is the default).
20
Setting the Day/Night Control
The table below explains the options on the DAY/NIGHT SETUP menu.
DAY/NIGHT SETUP
DAY/NIGHT SETUP
NIGHT MODE ..
AUTO
ON
10
> TDN DELAY
0
!
PREVIOUS PAGE .
Note
>DAY/NIGHT SETUP Select either:
<AUTO> (default) depending on light level, the camera automatically switches from
color to black and white.
<OFF> the camera stays color mode regardless of light level.
<ON> the camera stays in black and white mode regardless of light level.
>CLR BURST
>TDN DELAY
The CLR BURST screen determines the video signal type used when the camera
switches from color to black and white mode. The options are:
<ON> (default) B/W with color burst.
<OFF> B/W without color burst.
Sets the time period in seconds that the camera waits before switching modes. This
prevents unnecessary switching (for example, when an object passes briefly in front of
the camera.)
Note
Certain video recorders require color carrier/burst to operate.
Document 800-00031 Rev A
04/08
21
Restoring Settings
On the main MENU, select RESTORE DEFAULTS, then YES followed by ENTER (middle
button). This reloads the factory default camera settings.
Caution
This action replaces all custom settings.
MENU
CAMERA SETUP …
VIEWING
WDR PRESETS
…
<Custom>
DAY/NIGHT SETUP …
VERSION …
RESTORE DEFAULTS <YES>
>
EXIT
22
Installing the Enclosure Cover
To install the enclosure cover, use the Allen key (supplied) to secure the HD4U/X dome
enclosure to the base with four #8-32 security screws.
Figure 7
Enclosure Cover Installation
HD4U/X dome enclosure
#8-32 security screws (x3)
Routine Maintenance
Use regular liquid cleaners to remove dirt and grime from the HD4U/X dome.
Caution
Do not use harsh or abrasive cleaners which can scratch the polycarbonate
dome and reduce visibility for the camera.
If the camera view is obstructed by scratches, remove the front plate and rotate to find an
unscratched part of the dome.
Document 800-00031 Rev A
04/08
23
Solving Common Technical Issues
❐
Check that the power supply voltage is within the operating specifications for your camera
No Video
❐
❐
Check the video signal connections are correct.
Check for a loose connection.
❐
❐
Check that the video ground connections.
Check for ground loops.
Fuzzy Video
❐
Select the Wide Dynamic Preset that gives you the best picture for your scene. If you still
have the problem, go to the CUSTOM menu and reduce the dynamic range slider to a
lower value. Using the VIEWING menu, set the resolution to High and Sharpness to
Normal or to Sharp.
Image has a
white cast
❐
The WDR presets consist of 3 main types—center-weighted scene, full scene, and full
scene with spot glare. Depending on the scene, you can narrow down your choice to the
presets within each of these groups. Most applications can use the full scene presets—
INDOOR or OUTDOOR—as these are optimized for general lighting conditions.
Which
preset is
right?
If the area of interest is primarily in the center of the scene, use the ATM, LOADING DOCK,
or LOBBY presets.
For scenes in which there are hot spots of illumination and angle of view, the GAMING
and LICENSE PLATE presets will offer the best picture quality for seeing the objects of
interest.
❐
The WDR presets set the dynamic range, the exposure, sharpness, and the AGC level.
Changing any of these changes the WDR preset to Custom. The preset that you selected
was still loaded, except that the AGC had changed, thus customizing your setup. Custom
allows you to modify the dynamic range and exposure of the preset.
Changing
AGC value
affectsWDR
preset
24
Warranty and Service
Subject to the terms and conditions listed on the Product warranty, during the warranty
period Honeywell will repair or replace, at its sole option, free of charge, any defective
products returned prepaid.
In the event you have a problem with any Honeywell product, please call Customer Service
at 1.800.796.CCTV for assistance or to request a Return Merchandise Authorization
(RMA) number.
Be sure to have the model number, serial number, and the nature of the problem available
for the technical service representative.
Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped
to Honeywell without a clearly identified Return Merchandise Authorization (RMA)
number may be refused.
Document 800-00031 Rev A
04/08
25
Specifications
NTSC
PAL
625 lines, 2:1 interface
Progressive
Video Signal Specifications
Video Standard:
525 lines, 2:1 interface
Scanning System:
Image Sensor:
1/3 in. WDR digital image device
720 (H) x 540 (V)
Number of Pixels (H x V):
Dynamic Range:
102dB typical, 120dB max
Infrared (IR) cut filter
No filter
Day/Night Operation:
Day:
Night:
Minimum Illumination:
Horizontal Resolution:
Lens Type:
0.4 lux @ F1.4
520 TV lines
2.8 – 10 mm @ F1.4 (IR corrected)
1 V p-p composite @ 75 Ohms
Video Output:
Sync System:
12 VDC: Internal
24 VAC: Line lock
Signal to Noise Ratio:
Auto Gain Control (AGC):
Automatic Electronic Shutter (AES):
Lens Iris Control:
50 dB typical
Auto (0–36 dB maximum)
1/60–1/100,000 sec
1/50–1/100,000 sec
DC drive
White Balance:
ATW/AWB/ATW Xtnd/Manual
Line Lock Phase Adjust:
Electrical Specifications
Input Voltage:
Adjustable line lock vertical phase, 180°
12 VDC / 24 VAC
11–16 VDC / 17– 28 VAC
1.5 kW transient
3.0 W
Input Range:
Surge Suppression:
Power Consumption:
26
Temperature:
Operating: -13°F to +122°F (-25°C to +50°C)
Storage: -4°F to +140°F (-20°C to +60°C)
Mechanical Specifications
Dimensions (D) x (H):
Weight:
5.5 in. x 3.6 in.(140.2 mm x 91.5 mm)
2.5 lb. (1.1 kg) max
Diecast aluminum
Housing Construction:
Housing Finish:
Video Output:
Power Input:
Powder coated
BNC connector
12-inch tinned leads
Regulatory
Emissions:
FCC, CE (EN55013)
CE (EN50130-4)
EU: 73/23/EEC LVD)
Meets IP66
Immunity:
Safety:
Environmental:
UL:
CAN/UL60065
3.26” (82.8 mm)
Dimensions
1.63”
(41.4 mm)
2.9” (74.8 mm)
4.9” (124.6 mm)
Document 800-00031 Rev A
04/08
27
Cable Guidelines
Maximum Power Supply Cable Length (feet/meters)
Cameras With AC/DC Power Supplies
Wire gauge
Total
load
Power
supply
24 AWG
22 AWG
18 AWG
16 AWG
3.5 W
3.5 W
15 VDC
24 VAC
200/61
325/99
826/252
1315/401
771/235
1512/461
3835/1169
6187/1886
Note Calculations are based on an unregulated linear power supply, which would be
the worst case. Using a regulated or switching power supply can increase the
cable distance. Honeywell recommends using a CSA Certified/UL listed Class
2 power adapter to ensure compliance with electrical safety standards.
Maximum Video Coaxial Cable Length (feet/meters)
Cable type
Wire gauge
RG-59
RG-6
RG-11
23 AWG*
750/229
18 AWG*
1500/457
14 AWG*
2000/610
Maximum length (feet/meters)
* Copper clad steel core, 95% braided shield
28
30
Document 800-00031 Rev A
04/08
31
Honeywell Video Systems (Head Office)
2700 Blankenbaker Pkwy, Suite 150
Louisville, KY 40299, USA
℡ +1.800.796.2288
Honeywell Video Systems Northern Europe
Netwerk 121
1446 WV Purmerend, The Netherlands
℡ +31.299.410.200
Honeywell Security Australia Pty Ltd.
Unit 5, Riverside Centre, 24-28 River Road West
Parramatta, NSW 2150, Australia
℡ +61.2.8837.9300
Honeywell Systems Group
Aston Fields Road, Whitehouse Ind Est
Runcorn, Cheshire, WA7 3DL, UK
℡ +44 (0)1928 756999
Honeywell Security Asia Pacific
33/F Tower A, City Center, 100 Zun Yi Road
Shanghai 200051, China
℡ +86 21.2527.4568
Honeywell Security South Africa
Unit 6 Galaxy Park, 17 Galaxy Avenue
Linbro Park, P.O. Box 59904
2100 Kengray, Johannesburg, South Africa
℡ +27.11.574.2500
Honeywell Security Asia
Flat A, 16/F, CDW Building, 388 Castle Peak Road
Tsuen Wan, N.T., Hong Kong
℡ +852.2405.2323
Honeywell Security Deutschland
Johannes-Mauthe-Straße 14
D-72458 Albstadt, Germany
℡ +49.74 31.8 01.0
Honeywell Security France
Parc Gutenberg, 8, Voie La Cardon
91120, Palaiseau, France
℡ +33.01.64.53.80.40
Honeywell Security Poland
Chmielewskiego 22a, 70-028
Szczecin, Polska
℡ +48.91.485.40.60
Honeywell Security Italia SpA
Via della Resistenza 53/59
20090 Buccinasco
Honeywell Security Czech Republic
Havránkova 33, Brno
Milan, Italy
℡ ++39.02.48880551
Dolní Heršpice, 619 00, Czech Republic
℡ +420.543.558.111
Honeywell Security España
Mijancas 1. 3 Planta
P. Ind. Las Mercedes
28022 Madrid, Spain
℡ +34.902.667.800
Honeywell Security Slovakia Republic
Vajnorská 142, 83104 Bratislava
Slovakia
℡ +421.2.444.54.660
a
+1.800.796.CCTV (North America only)
Document 800-00031 – Rev A – 04/08
© 2008 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written
permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However,
Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof. The information contained
herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
|
